Skip to main content
True Value
Project

Reassemble the tap — Install the New Delta Shower Faucet Trim

Beginner2 hours

Part of project

How to Replace a Delta Shower Faucet: A Step-by-Step DIY Guide · Step 4 of 5

Helpful?

In this video

Reassemble the tap by screwing on the nut, decorative cover, lever handle, and lever cap. Make sure each component is secured and tightened properly.

Goal: Put the tap back together

Used in this video

  • Footprints or grips (brand: Unknown, Pliers_Type: Footprints, Grips) · optional — Tightening nuts
  • Allen key (brand: Unknown, Screwdriver_Tip: Allen, Allen Wrench Size: Metric) · optional — Tightening the lever screw
141.4K views1.0K2 minutes
This Old House

2.2M subscribers

View Channel

FAQs

How do I turn off the water to my shower if I can't find a dedicated shut-off valve?

First, locate the main water shut-off valve for your entire house, usually near the water meter or where the main line enters. Turn this valve clockwise until the water flow stops completely. If you live in an apartment or multi-unit building, you may need to contact your building's maintenance or management for assistance, as there might be a central shut-off.

What specific tools are most important to have on hand for removing the Delta handle and trim?

You'll definitely need a Phillips head screwdriver. Many Delta handles also use a small set screw, so having a set of Allen wrenches (hex keys) on hand, typically 1/8" or 3/32", is crucial. A flathead screwdriver can also be useful for gently prying off the trim plate, and a utility knife might help score old caulk.

My new Delta trim is installed, but I'm getting a small drip from the showerhead or around the handle. What should I check?

Ensure all screws, especially those securing the escutcheon plate and handle, are tightened firmly but not overtightened. For drips from the showerhead, verify that any new rubber gaskets or O-rings are properly seated and not pinched. Sometimes, a slight adjustment to the trim or confirming the cartridge (if replaced) is fully engaged can resolve minor leaks.

The project summary mentions taking photos during removal. Why is this important, and what should I focus on?

Taking photos is crucial for beginners to remember the exact order and orientation of parts, especially for the handle and trim components, which can have specific alignments. Focus on capturing screw locations, how parts are layered, and the positions of gaskets or washers. These photos serve as a valuable reference during reassembly to ensure everything goes back correctly.

Transcript
Hide

go the back one other thing putting it back I've slotted it back in the little slots at the back might be worth getting another one of those because that's the one that goes in there like that because then that will sit on top of that and screw down once you're happy with that little washer you can carry on so take it out again just to show you and that's it there that one just make sure there's no problems really at all it's fine it's not that by the way it's got a couple of little holes in it there let's see it and you're just going to make sure that they're at the bottom okay so it goes in nice before we put it on and then just fill it in make sure we're still seated and hold it if you'd rather make sure it doesn't move out of the little spot okay push that in now we'll need a little new part and again I always use footbridge but you can use grips just to tighten it up a little bit put those on just give it a little bit careful with the freight you can use some cloth around there if you'd rather okay just to give it a nipping okay tell you if it's just about right and if it was about right and then you can fit this back on a little cover followed by a top and he wants that to screw it on that back on put our LNP screw it back in so I'll put it back there and just do it back in on never to get right out I'll never do too much of a jump to get back in once that's here sure it's tight and so it feels like it's working okay we're ready to put a little bit in the front here we took out make sure it's plugged in the sink again okay and push it back in it's got a cold and hot side do it but I know which side it goes so there is a little hot and cold on it but it's up to you most haven't got anything at all and that's it now it's on a warm job should be done okay a different ending for a change okay that's about it and let's start

Auto-generated transcript. May contain errors.