Skip to main content
True Value
Project

Prepare the Pipe End — Clean and Deburr the Pipe Ends

Beginner3 hours

Part of project

How to Repair a Leaking Copper Pipe with a Compression Coupling · Step 4 of 7

Helpful?

In this video

Examine the end of the pipe that was inserted into the fitting. The pipe end must be perfectly round, clean, and smooth. If the cut is jagged or angled, use the correct pipe cutter for the material (e.g., a copper tubing cutter for copper, a ratchet-style cutter for PEX) to make a fresh, square cut. Use a deburring tool to remove any sharp edges or burrs from both the inside and outside of the pipe end. If the pipe surface is deeply scratched, painted, or heavily sanded in the area where the O-ring seals, this can cause a leak. Cut the pipe back to a clean, undamaged section.

Goal: Ensure the pipe has a clean, smooth, and square end for the O-ring to seal against.

  • Using a hacksaw can create a rough cut with burrs that will damage the O-ring and cause a leak. Always use a designated pipe cutter.
  • Deburring is a critical step; a small burr on the pipe's edge can easily slice the O-ring during installation.

Used in this video

  • Pipe Cutter (Tool Type: Tubing cutter) — Making a clean, square cut on the pipe
  • Deburring Tool (brand: SharkBite, Deburring_Tool_Type: Manual_deburring_tool) — Smoothing the cut edge of the pipe to prevent damage to the O-ring
  • Sandpaper (Sandpaper_Grit: Fine) · optional — Lightly cleaning the outside of a copper pipe or removing paint
51.8K views15810 minutes
ExpertVillage Leaf Group

3.6M subscribers

View Channel

FAQs

How difficult is this repair for a beginner, and what if it takes longer than 3 hours?

This repair is rated beginner because it avoids complex techniques like soldering. While the estimated time is 3 hours, allow extra time for locating the leak, gathering tools, and ensuring the pipe system is fully drained. Rushing can lead to mistakes, so prioritize careful, precise work over speed.

Do I really need all the specific tools listed, or can I use substitutes for this project?

While tools like a dedicated tubing cutter and reamer are highly recommended for achieving clean, burr-free pipe ends crucial for a leak-proof seal, some items like permanent markers or measuring tape can be substituted with similar household tools. An adjustable wrench is essential, so ensure you have one that fits the coupling nuts securely.

What's the most common mistake beginners make with compression fittings, and how can I avoid a new leak?

The most common mistake is not properly preparing the pipe ends (cutting straight, deburring, and cleaning) or improperly tightening the compression nuts. Ensure pipe ends are perfectly smooth and burr-free, and tighten the nuts until snug, then give an additional 1/2 to 3/4 turn. Avoid over-tightening, which can deform the ferrule or strip threads, or under-tightening, which causes leaks.

What are the most important safety precautions I should take when repairing a leaking copper pipe?

Always shut off the main water supply and drain the pipes completely before starting to prevent water damage and potential electrical hazards. Wear safety glasses to protect your eyes from debris, especially when cutting or deburring the pipe. Be mindful of sharp edges on cut pipes.

Transcript
Hide

short-bite fitting for your pipe. Number 5. You're using the wrong fitting for your pipe's short-bite fittings or does I need to be used with certain types of pipes. Using these nifty fittings with the wrong type of pipe can result in fitting that leaks. Packs, copper, CPC, PRT, and HDP pipes are compatible with short-bite fittings. For example, Packs L-Packs pipes cannot be used with short-bite fittings. How to fix it? To verify that this is the reason for your leak, you'll need to verify the type of pipe you're using. You'll then want to ensure that it is, in fact, compatible with the short-bite fitting. If it is not compatible, you'll need to use an appropriate fitting for your relevant pipes. Number 6. Your pipes are deformed sometimes the leak isn't the result of a faulty short-bite fitting, but rather due to a deformed pipe. Pipes often deal with extreme temperatures and will, over time, become warped. This could simply be due to the age of your pipes. However, the compromised pipe can result in a leaking push fitting. How to fix it? To address this issue, you'll need to replace the section of the damaged pipe. Once you've connected the replacement pipe to the short-bite fitting, your leak will be a problem of the past. Number 7. Your pipes are painted painting your pipes can also result in a bad seal between your short-bite fitting and the pipe. With a dry paint on your pipes presses against the short-bite fittings cufflink, the seal strength can be compromised. In turn, this can result in a leak. How to fix it, if you find that the pipe where the short-bite fitting is leaking is indeed painted, it could be the cause of your leak. To fix this, you'll need to turn off your home's water and disconnect the pipe. With sandpaper or paint stripping product, you can remove the paint near the end of the pipe, where the fitting will be located. Once the paint has been removed, you can reconnect the fitting. Number 8. You've sanded copper pipes sanding copper is an easy way to smooth it out. However, when it comes down to copper pipes with short-bite fittings, you should avoid sanding your pipes. That's because the process of sanding creates an uneven surface. In turn, this compromise is the effectiveness of your push fitting and could result in a leak. How to fix it, if you've sanded your copper pipes, you might need to replace parts of your pipe. Doing this will repair the leaking short-bite fitting. In the future, you should only use very fine sanding…

Auto-generated transcript. May contain errors.