Disconnect Old Faucet and Supply Lines — Disconnect the Leaking Supply Line
Part of project
How to Fix a Leak at a Faucet Supply Line Connection · Step 2 of 5
In this video
Using an adjustable wrench, loosen and unscrew the nuts connecting the hot and cold water supply lines from the shut-off valves. Next, locate the mounting hardware holding the old faucet in place under the sink. Use a socket wrench or basin wrench to loosen and remove the nuts securing the faucet.
Goal: Detach the old faucet from the sink and plumbing.
Used in this video
- Adjustable Wrench (Tool Type: Wrench_Type) — Loosening the nuts on the water supply lines.
- Socket Wrench (Tool Type: Fastener_Tool) — Removing the mounting nuts holding the old faucet.
719K subscribers
FAQs
How long does a beginner typically need to fix a faucet supply line leak, and what's the most common hold-up?
For most beginners, this project takes about 30-60 minutes. The biggest time-consumer is often preparing the work area, ensuring the water is fully off, and carefully tightening the new connections to avoid overtightening or cross-threading.
The project mentions a 'Braided Polymer Faucet Supply Line.' Are there other types, and how do I ensure I get the right replacement?
Yes, supply lines come in various materials like braided stainless steel or PEX, which are also durable options. The most critical step is to match the length and the connector sizes (e.g., 3/8 in. compression x 1/2 in. FIP) of your new line to your existing one and the connections on your faucet and shut-off valve.
I've replaced the supply line, but it's still leaking slightly after installation. What's the first thing I should check?
First, ensure both nuts are snug but not overtightened; over-tightening can damage internal washers or threads. Confirm the supply line is seated straight without cross-threading, and visually check that the small rubber washer inside the faucet connection is present and intact, as this creates the primary seal.
Is it ever okay to just tighten the old leaky supply line connection instead of replacing the entire line?
You can attempt a slight turn with your wrench to see if it stops the leak, but if it's an older line or already tight, this often isn't a permanent fix and could worsen the leak. Replacing the inexpensive supply line ensures a fresh, reliable seal, especially if the internal washers are worn or compressed.
TranscriptHide
Auto-generated transcript. May contain errors.
Disconnect Old Faucet and Supply Lines — Disconnect the Leaking Supply Line
Part of project
How to Fix a Leak at a Faucet Supply Line Connection · Step 2 of 5
In this video
Using an adjustable wrench, loosen and unscrew the nuts connecting the hot and cold water supply lines from the shut-off valves. Next, locate the mounting hardware holding the old faucet in place under the sink. Use a socket wrench or basin wrench to loosen and remove the nuts securing the faucet.
Goal: Detach the old faucet from the sink and plumbing.
Used in this video
- Adjustable Wrench (Tool Type: Wrench_Type) — Loosening the nuts on the water supply lines.
- Socket Wrench (Tool Type: Fastener_Tool) — Removing the mounting nuts holding the old faucet.
Frequently Asked Questions
How long does a beginner typically need to fix a faucet supply line leak, and what's the most common hold-up?
For most beginners, this project takes about 30-60 minutes. The biggest time-consumer is often preparing the work area, ensuring the water is fully off, and carefully tightening the new connections to avoid overtightening or cross-threading.
The project mentions a 'Braided Polymer Faucet Supply Line.' Are there other types, and how do I ensure I get the right replacement?
Yes, supply lines come in various materials like braided stainless steel or PEX, which are also durable options. The most critical step is to match the length and the connector sizes (e.g., 3/8 in. compression x 1/2 in. FIP) of your new line to your existing one and the connections on your faucet and shut-off valve.
I've replaced the supply line, but it's still leaking slightly after installation. What's the first thing I should check?
First, ensure both nuts are snug but not overtightened; over-tightening can damage internal washers or threads. Confirm the supply line is seated straight without cross-threading, and visually check that the small rubber washer inside the faucet connection is present and intact, as this creates the primary seal.
Is it ever okay to just tighten the old leaky supply line connection instead of replacing the entire line?
You can attempt a slight turn with your wrench to see if it stops the leak, but if it's an older line or already tight, this often isn't a permanent fix and could worsen the leak. Replacing the inexpensive supply line ensures a fresh, reliable seal, especially if the internal washers are worn or compressed.
Video Transcript
(1,167 characters)Hide
Video Transcript
(1,167 characters)Transcript may be auto-generated and contain errors.