Connect Plumbing Lines — Install the Water Supply Lines
Part of project
Shower Rough-In Plumbing: A Step-by-Step DIY Guide · Step 3 of 4
In this video
Connect the hot and cold water supply lines from the faucet to the corresponding shutoff valves on the wall. Hand-tighten the connections, then use pliers to give them a final quarter-turn. Next, connect the P-trap assembly to the sink's drain tailpiece and the drain pipe in the wall. Ensure all slip-joint nuts are tightened securely to prevent leaks.
Goal: Connect Water and Drain Lines
Used in this video
- Pliers (Pliers_Type: Channel-Lock) — Tightening the nuts on the water supply lines and P-trap.
603K subscribers
FAQs
How difficult is this shower rough-in project for a beginner, and what's a realistic time estimate?
While labeled "beginner," this project requires meticulous attention to detail for measurements and connections. A novice can accomplish it, but allocate at least a full weekend, or even longer, to work carefully, learn the process, and handle any unforeseen challenges without rushing.
The tool list includes a "Zest Candle." Is that correct, and are the PEX-specific tools like the crimp tool absolutely necessary?
The "Zest Candle" is an error and is not needed for plumbing. However, specialized PEX tools such as the PEX cutter and a crimp tool are absolutely essential for creating secure, leak-proof connections. You can often rent these specific PEX tools from home improvement stores if you prefer not to purchase them.
What are the most common causes of leaks in PEX supply lines, and how can I ensure my connections are watertight?
Leaks typically stem from improper crimping or damaged tubing. Always make clean, perpendicular cuts with your PEX cutter, ensure fittings are fully seated, and use your crimp tool correctly. Crucially, check every crimped connection with a go/no-go gauge for proper tightness.
How should I thoroughly test the PEX supply lines for leaks before closing up the walls?
After capping all open PEX ends, slowly introduce water pressure to the system. Inspect every connection point visually for drips, listen for any hissing, and feel for moisture. Keep the system pressurized for several hours and re-check periodically to catch any slow leaks before proceeding.
TranscriptHide
Auto-generated transcript. May contain errors.
Connect Plumbing Lines — Install the Water Supply Lines
Part of project
Shower Rough-In Plumbing: A Step-by-Step DIY Guide · Step 3 of 4
In this video
Connect the hot and cold water supply lines from the faucet to the corresponding shutoff valves on the wall. Hand-tighten the connections, then use pliers to give them a final quarter-turn. Next, connect the P-trap assembly to the sink's drain tailpiece and the drain pipe in the wall. Ensure all slip-joint nuts are tightened securely to prevent leaks.
Goal: Connect Water and Drain Lines
Used in this video
- Pliers (Pliers_Type: Channel-Lock) — Tightening the nuts on the water supply lines and P-trap.
Frequently Asked Questions
How difficult is this shower rough-in project for a beginner, and what's a realistic time estimate?
While labeled "beginner," this project requires meticulous attention to detail for measurements and connections. A novice can accomplish it, but allocate at least a full weekend, or even longer, to work carefully, learn the process, and handle any unforeseen challenges without rushing.
The tool list includes a "Zest Candle." Is that correct, and are the PEX-specific tools like the crimp tool absolutely necessary?
The "Zest Candle" is an error and is not needed for plumbing. However, specialized PEX tools such as the PEX cutter and a crimp tool are absolutely essential for creating secure, leak-proof connections. You can often rent these specific PEX tools from home improvement stores if you prefer not to purchase them.
What are the most common causes of leaks in PEX supply lines, and how can I ensure my connections are watertight?
Leaks typically stem from improper crimping or damaged tubing. Always make clean, perpendicular cuts with your PEX cutter, ensure fittings are fully seated, and use your crimp tool correctly. Crucially, check every crimped connection with a go/no-go gauge for proper tightness.
How should I thoroughly test the PEX supply lines for leaks before closing up the walls?
After capping all open PEX ends, slowly introduce water pressure to the system. Inspect every connection point visually for drips, listen for any hissing, and feel for moisture. Keep the system pressurized for several hours and re-check periodically to catch any slow leaks before proceeding.
Video Transcript
(166 characters)Hide
Video Transcript
(166 characters)Transcript may be auto-generated and contain errors.