Reassemble Drain Line — Assemble Non-Disposal Side Drain
Part of project
How to Plumb a Double Kitchen Sink Drain with a Garbage Disposal · Step 3 of 8
In this video
Take the cut waste arm. Remove the temporary nut and washer from the dishwasher tailpiece. Slide the slip nut and the beveled washer onto the straight end of the cut waste arm. Then, insert this end into the dishwasher tailpiece. On the elbow end of the waste arm, place the flat washer and connect it to the sink strainer. Hand-tighten all slip nuts securely.
Goal: Plumbing Pipes Installation
- Ensure the beveled washer's tapered side faces the tailpiece and the flat washer is used on the strainer side for proper sealing.
- Hand-tighten the nuts first. If there are leaks after testing, you can use channel-lock pliers to give them a slight quarter-turn, but be careful not to over-tighten and crack the plastic.
2K subscribers
FAQs
How difficult is it to plumb a double kitchen sink with a garbage disposal for a beginner, and how long should I expect it to take?
This project is rated as beginner-friendly, but requires patience and attention to detail. For a DIY novice, plan to set aside 3-5 hours, especially if you encounter unexpected issues or need to make precise cuts. The material cost, including the disposal and plumbing parts, typically ranges from $150-$400 depending on the quality and features chosen.
Are all the listed tools, especially specialized cutters and reamers, truly essential for this plumbing project?
While basic tools like Channellock pliers and a screwdriver are essential, specialized tools like the RIDGID PTEC 3000 plastic tubing cutter and the Husky Reamer are highly recommended. They ensure clean, burr-free cuts on plastic pipes, which significantly reduces the risk of leaks and makes assembly much easier. You could use a hacksaw for cuts, but meticulous deburring would then be critical.
What are the most common mistakes that lead to leaks after installing a double sink drain and garbage disposal, and how can I prevent them?
The most common causes of leaks are improperly tightened slip-nut connections, not using plumber's putty correctly around the sink flange, and misaligned P-trap components. Always hand-tighten slip nuts first, then use your Channellock pliers for an additional half-turn, ensuring all washers are seated perfectly. Thoroughly test for leaks by running water and inspecting every connection with paper towels.
What specific safety precautions should I take when working under the sink, especially with a garbage disposal and water lines?
Safety is paramount. Always disconnect power to the garbage disposal at the circuit breaker before beginning any work on it. Turn off the water supply to the sink at the shut-off valves or main house valve. Wear safety glasses to protect your eyes from debris, and use gloves to avoid contact with old grime or chemicals.
TranscriptHide
Auto-generated transcript. May contain errors.
Reassemble Drain Line — Assemble Non-Disposal Side Drain
Part of project
How to Plumb a Double Kitchen Sink Drain with a Garbage Disposal · Step 3 of 8
In this video
Take the cut waste arm. Remove the temporary nut and washer from the dishwasher tailpiece. Slide the slip nut and the beveled washer onto the straight end of the cut waste arm. Then, insert this end into the dishwasher tailpiece. On the elbow end of the waste arm, place the flat washer and connect it to the sink strainer. Hand-tighten all slip nuts securely.
Goal: Plumbing Pipes Installation
- Ensure the beveled washer's tapered side faces the tailpiece and the flat washer is used on the strainer side for proper sealing.
- Hand-tighten the nuts first. If there are leaks after testing, you can use channel-lock pliers to give them a slight quarter-turn, but be careful not to over-tighten and crack the plastic.
Frequently Asked Questions
How difficult is it to plumb a double kitchen sink with a garbage disposal for a beginner, and how long should I expect it to take?
This project is rated as beginner-friendly, but requires patience and attention to detail. For a DIY novice, plan to set aside 3-5 hours, especially if you encounter unexpected issues or need to make precise cuts. The material cost, including the disposal and plumbing parts, typically ranges from $150-$400 depending on the quality and features chosen.
Are all the listed tools, especially specialized cutters and reamers, truly essential for this plumbing project?
While basic tools like Channellock pliers and a screwdriver are essential, specialized tools like the RIDGID PTEC 3000 plastic tubing cutter and the Husky Reamer are highly recommended. They ensure clean, burr-free cuts on plastic pipes, which significantly reduces the risk of leaks and makes assembly much easier. You could use a hacksaw for cuts, but meticulous deburring would then be critical.
What are the most common mistakes that lead to leaks after installing a double sink drain and garbage disposal, and how can I prevent them?
The most common causes of leaks are improperly tightened slip-nut connections, not using plumber's putty correctly around the sink flange, and misaligned P-trap components. Always hand-tighten slip nuts first, then use your Channellock pliers for an additional half-turn, ensuring all washers are seated perfectly. Thoroughly test for leaks by running water and inspecting every connection with paper towels.
What specific safety precautions should I take when working under the sink, especially with a garbage disposal and water lines?
Safety is paramount. Always disconnect power to the garbage disposal at the circuit breaker before beginning any work on it. Turn off the water supply to the sink at the shut-off valves or main house valve. Wear safety glasses to protect your eyes from debris, and use gloves to avoid contact with old grime or chemicals.
Video Transcript
(447 characters)Hide
Video Transcript
(447 characters)Transcript may be auto-generated and contain errors.