Install Drain Saddle — Connect Disposal to Waste Tee
Part of project
How to Plumb a Double Kitchen Sink Drain with a Garbage Disposal · Step 4 of 8
In this video
To dispose of waste water, a drain saddle is installed on the sink's drain pipe. Position the saddle on a straight section of the PVC tailpiece, above the P-trap. Place the foam gasket, then clamp the two halves of the saddle around the pipe. Using a power drill, drill a hole through the opening in the saddle and into the PVC pipe. Once the hole is drilled, fully tighten the two bolts on the saddle to create a seal. Finally, connect the waste water tube from the filter to the barbed fitting on the saddle.
Goal: Create a drain connection for filter waste water
- Do not overtighten the saddle valve screws, as this can crack the plastic clamp or the drain pipe.
Used in this video
- Power Drill (brand: unknown) — Drilling a hole in the PVC drain pipe.
- Drill Bit (brand: unknown) — Creating the hole for the drain connection.
2K subscribers
FAQs
How difficult is it to plumb a double kitchen sink with a garbage disposal for a beginner, and how long should I expect it to take?
This project is rated as beginner-friendly, but requires patience and attention to detail. For a DIY novice, plan to set aside 3-5 hours, especially if you encounter unexpected issues or need to make precise cuts. The material cost, including the disposal and plumbing parts, typically ranges from $150-$400 depending on the quality and features chosen.
Are all the listed tools, especially specialized cutters and reamers, truly essential for this plumbing project?
While basic tools like Channellock pliers and a screwdriver are essential, specialized tools like the RIDGID PTEC 3000 plastic tubing cutter and the Husky Reamer are highly recommended. They ensure clean, burr-free cuts on plastic pipes, which significantly reduces the risk of leaks and makes assembly much easier. You could use a hacksaw for cuts, but meticulous deburring would then be critical.
What are the most common mistakes that lead to leaks after installing a double sink drain and garbage disposal, and how can I prevent them?
The most common causes of leaks are improperly tightened slip-nut connections, not using plumber's putty correctly around the sink flange, and misaligned P-trap components. Always hand-tighten slip nuts first, then use your Channellock pliers for an additional half-turn, ensuring all washers are seated perfectly. Thoroughly test for leaks by running water and inspecting every connection with paper towels.
What specific safety precautions should I take when working under the sink, especially with a garbage disposal and water lines?
Safety is paramount. Always disconnect power to the garbage disposal at the circuit breaker before beginning any work on it. Turn off the water supply to the sink at the shut-off valves or main house valve. Wear safety glasses to protect your eyes from debris, and use gloves to avoid contact with old grime or chemicals.
TranscriptHide
Auto-generated transcript. May contain errors.
Install Drain Saddle — Connect Disposal to Waste Tee
Part of project
How to Plumb a Double Kitchen Sink Drain with a Garbage Disposal · Step 4 of 8
In this video
To dispose of waste water, a drain saddle is installed on the sink's drain pipe. Position the saddle on a straight section of the PVC tailpiece, above the P-trap. Place the foam gasket, then clamp the two halves of the saddle around the pipe. Using a power drill, drill a hole through the opening in the saddle and into the PVC pipe. Once the hole is drilled, fully tighten the two bolts on the saddle to create a seal. Finally, connect the waste water tube from the filter to the barbed fitting on the saddle.
Goal: Create a drain connection for filter waste water
- Do not overtighten the saddle valve screws, as this can crack the plastic clamp or the drain pipe.
Used in this video
- Power Drill (brand: unknown) — Drilling a hole in the PVC drain pipe.
- Drill Bit (brand: unknown) — Creating the hole for the drain connection.
Frequently Asked Questions
How difficult is it to plumb a double kitchen sink with a garbage disposal for a beginner, and how long should I expect it to take?
This project is rated as beginner-friendly, but requires patience and attention to detail. For a DIY novice, plan to set aside 3-5 hours, especially if you encounter unexpected issues or need to make precise cuts. The material cost, including the disposal and plumbing parts, typically ranges from $150-$400 depending on the quality and features chosen.
Are all the listed tools, especially specialized cutters and reamers, truly essential for this plumbing project?
While basic tools like Channellock pliers and a screwdriver are essential, specialized tools like the RIDGID PTEC 3000 plastic tubing cutter and the Husky Reamer are highly recommended. They ensure clean, burr-free cuts on plastic pipes, which significantly reduces the risk of leaks and makes assembly much easier. You could use a hacksaw for cuts, but meticulous deburring would then be critical.
What are the most common mistakes that lead to leaks after installing a double sink drain and garbage disposal, and how can I prevent them?
The most common causes of leaks are improperly tightened slip-nut connections, not using plumber's putty correctly around the sink flange, and misaligned P-trap components. Always hand-tighten slip nuts first, then use your Channellock pliers for an additional half-turn, ensuring all washers are seated perfectly. Thoroughly test for leaks by running water and inspecting every connection with paper towels.
What specific safety precautions should I take when working under the sink, especially with a garbage disposal and water lines?
Safety is paramount. Always disconnect power to the garbage disposal at the circuit breaker before beginning any work on it. Turn off the water supply to the sink at the shut-off valves or main house valve. Wear safety glasses to protect your eyes from debris, and use gloves to avoid contact with old grime or chemicals.
Video Transcript
(209 characters)Hide
Video Transcript
(209 characters)Transcript may be auto-generated and contain errors.