Glue and Install the New Assembly — Install the AAV
Part of project
How to Install an Air Admittance Valve (AAV) · Step 6 of 7
In this video
Once you have confirmed the fit, begin gluing the assembly. Apply PVC primer to the outside of the pipe and the inside of the fitting for each connection. Immediately follow with an even coat of PVC cement. Push the pipe and fitting together with a slight twisting motion and hold for 30 seconds to ensure a strong bond. Connect the entire new assembly to the existing irrigation lines. Tighten the union by hand, plus a quarter-turn with a wrench if needed, but do not over-tighten.
Goal: Permanently install the new valve system
2K subscribers
FAQs
What are the most important safety precautions I should take when installing an AAV?
Always wear appropriate personal protective equipment, including safety glasses and gloves, especially when cutting PVC pipe and handling chemical solvents. Ensure the work area is well-ventilated when using PVC primer and cement to avoid inhaling fumes. Have a bucket ready to catch any residual water from the drain line.
Do I really need all those specific pipe cutters and deburring tools for this project, or can I use a simpler tool?
While a hacksaw can cut PVC, specialized pipe cutters (like the ratcheting PVC cutter or plastic tubing cutter) provide much cleaner, straighter cuts with less effort, which is crucial for a tight seal. A deburring tool is also highly recommended to smooth edges, preventing snags and ensuring the best bond with primer and cement.
How long does a typical AAV installation take for a beginner, and what's the estimated cost of materials?
For a beginner, this project typically takes 1 to 3 hours, depending on preparation and experience with plumbing. The material costs, including the AAV, PVC fittings, primer, and cement, usually range from $30-$60, assuming you already have basic tools like a tape measure and bucket.
Where is the ideal location to install an AAV on a sink drain line for optimal performance and code compliance?
The AAV must be installed vertically, at least 4 inches above the horizontal drainpipe it serves, and critically, above the fixture's flood level rim. This prevents water from entering the valve and ensures proper air intake, while complying with most plumbing codes.
TranscriptHide
Auto-generated transcript. May contain errors.
Glue and Install the New Assembly — Install the AAV
Part of project
How to Install an Air Admittance Valve (AAV) · Step 6 of 7
In this video
Once you have confirmed the fit, begin gluing the assembly. Apply PVC primer to the outside of the pipe and the inside of the fitting for each connection. Immediately follow with an even coat of PVC cement. Push the pipe and fitting together with a slight twisting motion and hold for 30 seconds to ensure a strong bond. Connect the entire new assembly to the existing irrigation lines. Tighten the union by hand, plus a quarter-turn with a wrench if needed, but do not over-tighten.
Goal: Permanently install the new valve system
Frequently Asked Questions
What are the most important safety precautions I should take when installing an AAV?
Always wear appropriate personal protective equipment, including safety glasses and gloves, especially when cutting PVC pipe and handling chemical solvents. Ensure the work area is well-ventilated when using PVC primer and cement to avoid inhaling fumes. Have a bucket ready to catch any residual water from the drain line.
Do I really need all those specific pipe cutters and deburring tools for this project, or can I use a simpler tool?
While a hacksaw can cut PVC, specialized pipe cutters (like the ratcheting PVC cutter or plastic tubing cutter) provide much cleaner, straighter cuts with less effort, which is crucial for a tight seal. A deburring tool is also highly recommended to smooth edges, preventing snags and ensuring the best bond with primer and cement.
How long does a typical AAV installation take for a beginner, and what's the estimated cost of materials?
For a beginner, this project typically takes 1 to 3 hours, depending on preparation and experience with plumbing. The material costs, including the AAV, PVC fittings, primer, and cement, usually range from $30-$60, assuming you already have basic tools like a tape measure and bucket.
Where is the ideal location to install an AAV on a sink drain line for optimal performance and code compliance?
The AAV must be installed vertically, at least 4 inches above the horizontal drainpipe it serves, and critically, above the fixture's flood level rim. This prevents water from entering the valve and ensures proper air intake, while complying with most plumbing codes.
Video Transcript
(704 characters)Hide
Video Transcript
(704 characters)Transcript may be auto-generated and contain errors.