Check for Leaks — Final Checks and Testing
Part of project
How to Replace a Washing Machine Drain Hose · Step 7 of 7
In this video
Slowly turn the water supply lever back to the 'on' position. Carefully check all four connections for any drips or leaks. Once you've confirmed there are no leaks, run a short wash cycle on the machine. This will test the connections under operating pressure. Check again for any leaks during and after the cycle.
Goal: Check for Leaks
- If you see any drips, shut off the water immediately and tighten the leaking connection slightly before turning the water back on.
1.1M subscribers
FAQs
What type of drain hose should I buy, and does the length matter?
You'll need a corrugated or smooth appliance drain hose, such as the Everbilt 8 ft. Corrugated Washing Machine Discharge Hose. Ensure the new hose is long enough to reach the standpipe without tension or kinks, but not so excessively long that it creates unnecessary loops or becomes obstructed. Always verify the new hose's diameter matches your washing machine's outlet port for a secure connection.
What are the essential safety precautions I need to take before starting this project?
The most critical safety step is to unplug the washing machine from its power source to prevent electric shock. You must also turn off the water supply to the washing machine to avoid accidental flooding. Keep absorbent towels like WYPALL L40 Towels and a bucket, such as the Unger 6 Gal. Heavy-Duty Plastic Bucket, on hand for any residual water.
Is replacing a washing machine drain hose a difficult DIY project, and how long should it typically take?
This project is rated as 'beginner' difficulty, making it accessible for most DIYers. With the necessary tools like pliers and a screwdriver, it typically takes about 1-2 hours to complete from start to finish. This includes preparation, accessing connections, replacing the hose, and final leak testing.
What are common mistakes people make when installing a new drain hose, and how can I avoid them?
A common mistake is not securely fastening the hose to both the washing machine and the standpipe, which can lead to leaks or disconnections. Ensure all clamps are tightened properly and use cable ties, like the Micro Connectors Cable Zip Ties, for extra security. Also, avoid kinking the hose, as this restricts drainage and can cause backflow.
TranscriptHide
Auto-generated transcript. May contain errors.
Check for Leaks — Final Checks and Testing
Part of project
How to Replace a Washing Machine Drain Hose · Step 7 of 7
In this video
Slowly turn the water supply lever back to the 'on' position. Carefully check all four connections for any drips or leaks. Once you've confirmed there are no leaks, run a short wash cycle on the machine. This will test the connections under operating pressure. Check again for any leaks during and after the cycle.
Goal: Check for Leaks
- If you see any drips, shut off the water immediately and tighten the leaking connection slightly before turning the water back on.
Frequently Asked Questions
What type of drain hose should I buy, and does the length matter?
You'll need a corrugated or smooth appliance drain hose, such as the Everbilt 8 ft. Corrugated Washing Machine Discharge Hose. Ensure the new hose is long enough to reach the standpipe without tension or kinks, but not so excessively long that it creates unnecessary loops or becomes obstructed. Always verify the new hose's diameter matches your washing machine's outlet port for a secure connection.
What are the essential safety precautions I need to take before starting this project?
The most critical safety step is to unplug the washing machine from its power source to prevent electric shock. You must also turn off the water supply to the washing machine to avoid accidental flooding. Keep absorbent towels like WYPALL L40 Towels and a bucket, such as the Unger 6 Gal. Heavy-Duty Plastic Bucket, on hand for any residual water.
Is replacing a washing machine drain hose a difficult DIY project, and how long should it typically take?
This project is rated as 'beginner' difficulty, making it accessible for most DIYers. With the necessary tools like pliers and a screwdriver, it typically takes about 1-2 hours to complete from start to finish. This includes preparation, accessing connections, replacing the hose, and final leak testing.
What are common mistakes people make when installing a new drain hose, and how can I avoid them?
A common mistake is not securely fastening the hose to both the washing machine and the standpipe, which can lead to leaks or disconnections. Ensure all clamps are tightened properly and use cable ties, like the Micro Connectors Cable Zip Ties, for extra security. Also, avoid kinking the hose, as this restricts drainage and can cause backflow.
Video Transcript
(365 characters)Hide
Video Transcript
(365 characters)Transcript may be auto-generated and contain errors.